• Cisco Packet Tracer Labs

In this Cisco Packet Tracer Page, you will find a lot of Cisco Packet Tracer Labs. You can download these Packet Tracer Labs with “.pkt” format and then you can use these lab topologies and configurations for you certification studies. You can use Cisco Packet Tracer for all your Cisco Certifications especially for CCENT, CCNP (, ) and.To gain more experience on Cisco CLI, Cisco Packet Tracer is the best tool especially for the beginners and the intermediate level. Because Packet Tracer is easy to use and it is very userfriendly.

You can reach many Cisco commands on the real router with Packet Tracer commands. There can be some limitations because of the fast that at the end of the day Packet Tracer is a simulator. But Packet Tracer commands will be enough for many of your Cisco certification practice scenarios.Basically we can divide the Packet Tracer Labs on IPCisco.com into four. These packet tracer lab categories are:. Cisco Packet Tracer Labs CCENT. Cisco Packet Tracer Labs CCNA. Cisco Packet Tracer Labs CCNP.

Cisco Packet Tracer Labs CCIEPacket Tracer Labs CCENTCCENT is the beginner certification of a network technician. As a network technician you can use Cisco Packet Tracer to gain hands on experience on Cisco CLI. There are a lot of lessons and labs on IPCisco.com for within Packet Tracer Labs CCENT. You can download the lab files with “.pkt” format and start to study for your CCENT certification with Packet Tracer commands on your own pc. Packet Tracer Labs CCNAis the most known beginning network certification.

With, you will learn the fundamentals of networks and you will gain hands on experience on Cisco CLI before the CCNA exams. Cisco Packet Tracer is a nice tool for CCNA exam lab trainings. In IPCisco.com, there are many Packet Tracer CCNA labs. You can download these Packet Tracer CCNA Labs and then you can practice on them on your own pc. Packet Tracer Labs CCNPAt the beginning Packet Tracer were known as a beginner tool and it was used by CCENT and studies. But after the enhanceents of Cisco Packet Tracer, Packet Tracer commands are also increase and new devices are added. For many CCNP lab scenario (, ), you can use Cisco Packet Tracer and you can practice with the lessons about Packet Tracer Labs CCNP on ipcisco.com.Packet Tracer Labs CCIEneed more practice.

During these practices you will benefit from many simulations and emulations beside real routers. Packet Tracer is also a nice tool to practice your scenarios. For a candidate, Packet Tracer can seem a little simple. But, in real Cisco Packet Tracer is very strong and you can practice many Packet Tracer lab scenarios and Packet Tracer commands on this network simulator.Packet Tracer DownloadAt the beginning, as a network engineer I have remember that I was searching for Packet Tracer with “ packet tracer download cisco”, “ packet tracer dowload free”, “ cisco packet tracer download free” or “ cisco packet tracer download cisco”, etc. I am sure that you did this alsoJ But downloading Packet Tracer is not difficult.

Packet Tracer download is free and you can download Cisco Packet Tracer.Cisco Packet Tracer TutorialTo learn Cisco Packet Tracer, you can use a tutorial or you can learn on the Packet Tracer itself. There is also a “” course on ipcisco.com. You can learn how to sue Packet Tracer with this basic course, you can practice Packet Tracer commands.Each Packet Tracer Lab on IPCisco.com is like a Cisco Packet Tracer Labs Tutorial step by step.

Another post related to and this time learn how to configure routing? The configuration of OSPF routing protocol is easy as. The Open Shortest Path First (OSPF) is a routing protocol for wide area networks and enterprise network. OSPF is perhaps the most widely used interior gateway protocol (IGP) in large enterprise networks. The IS-IS is another link-state dynamic routing protocol, which is more common in large service provider networks. The most widely used exterior gateway protocol is the Border Gateway Protocol (BGP), the principal routing protocol between autonomous systems on the Internet.

OSPF Routing Lab ConfigurationDownload the lab from this post or create your own OSPF Routing Lab and try to learn OSPF Routing configuration using this step by step guide. Router 1: Do the basic configuration of your routers, switches and computers. Set the IP address for each interface the same as a screenshot. The diagram is classless IP addresses and sub-netted to many networks. So it means you must familiar with IP sub-netting and VLSM.

Configure OSPF Routing Packet Tracer – Technig R1enableR1#configure terminalEnter configuration commands, one per line. End with CNTL/Z.R1(config)#interface serial 1/3R1(config-if)#ip address 20.10.10.1 255.255.255.252R1(config-if)#no shutdownR1(config-if)#exitR1(config)#R1(config)#interface serial 1/1R1(config-if)#ip address 10.10.10.1 255.255.255.252R1(config-if)#clock rate 64000R1(config-if)#no shutdownR1(config-if)#exitR1(config)#R1(config)#interface serial 1/0R1(config-if)#ip address 10.10.10.5 255.255.255.252R1(config-if)#clock rate 64000R1(config-if)#no shutdownRouter 2: Do the following configuration for Router 2. Configure OSPF Routing R2(config)#interface serial 1/0R2(config-if)#ip address 10.10.10.6 255.255.255.252R2(config-if)#no shutdownR2(config-if)#exitR2(config)#interface fastEthernet 0/0R2(config-if)#ip address 192.168.10.1 255.255.255.0R2(config-if)#no shutdownRouter 3: Now try to set IP address for Router 3 interfaces also. Router Commands.

Router#enableRouter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname R3R3(config)#interface serial 1/0R3(config-if)#ip address 10.10.10.2 255.255.255.252R3(config-if)#no shutdownR3(config-if)#exitR3(config)#interface fastEthernet 0/0R3(config-if)#ip address 192.168.1.1 255.255.255.0R3(config-if)#no shutdownGood, the basic configuration has competed and now start configure OSPF routing protocol on this network. How to Configure OSPF Routing Protocol?The Lab is ready for routing, download and configures with the following step by step guide. In the router R1 configure OSFP routing with Router OSPF command. Configure OSPF Routing R1 R1enableR1#configure terminalEnter configuration commands, one per line. End with CNTL/Z.R1(config)#router ospf 1R1(config-router)#network 20.10.10.0 0.0.0.3 area 0R1(config-router)#network 10.10.10.0 0.0.0.3 area 0R1(config-router)#network 10.10.10.4 0.0.0.3 area 0R1(config-router)#The router OSPF command enables OSPF routing on the router, and the 1 before OSFP is the process ID of the OSFP Protocol. You can set different process id from “ 1-65535” for each router.The network command with network ID “ network 20.10.10.0” is the network identifier, and the “ 0.0.0.3″ is the wildcard mask of 20.10.10.0 network. Wildcard mask determines which interfaces to advertise because OSPF advertises interfaces, not networks.Now go to Router R3 and configure with the following commands.

R3enableR3#configure terminalEnter configuration commands, one per line. End with CNTL/Z.R3(config)#router ospf 1R3(config-router)#network 192.168.1.0 0.0.0.255 area 0R3(config-router)#network 10.10.10.0 0.0.0.3 area 0Don? So do the following for router R2. R2enableR2#configure terminalEnter configuration commands, one per line.

End with CNTL/Z.R2(config)#router ospf 1R2(config-router)#network 192.168.10.0 0.0.0.255 area 0R2(config-router)#network 10.10.10.4 0.0.0.3 area 0OK, OSPF routing configuration has been finished successfully, now test your network whether they can ping with each other or not. In my Lab they work perfect, you can download and see the result. Configure – Complete Lab.Related Search:OSPF configuration step by step.how to configure OSPF between two routers.how to configure OSPF on Cisco router packet tracer.OSPF configuration in packet tracer.OSPF basic configuration.simple OSPF configuration example.OSPF routing protocol configuration pdf.how to configure router in packet tracer.how to configure OSPF step by step. I think there is a “mistake” in your configuration.

Cisco Packet Tracer Labs

In fact, you do not advertise internet by this command: R1(config)#router ospf 1 R1(config-router)#network 20.10.10.0 0.0.0.3 area 0Here, you include internet on your area 0. I think the right configuration to do here, is to do a default static route on R1 and share it to the others by ospf like that:router ospf 1 passive-interface Serial1/3 #do not send Hello packets on this interface network 10.10.10.4 0.0.0.3 area 0 network 10.10.10.0 0.0.0.3 area 0 default-information originate #send default route to others routers in the area! Ip route 0.0.0.0 0.0.0.0 Serial1/3🙂.